- 您现在的位置：买卖IC网 > Sheet目录532 > VSOP38336 (Vishay Semiconductors)IC SIGNAL CONDITIONING 36KHZ QFN
VSOP383..
www.vishay.com
Vishay Semiconductors
ABSOLUTE MAXIMUM RATINGS (T amb = 25 °C, unless otherwise specified)
PARAMETER
Supply voltage
Supply current
Output voltage
Output sink current
Power dissipation
Operating temperature range
Storage temperature range
ESD stress, HBM
ESD stress, MM
TEST CONDITION
Pin 2
Pin 2
Pin 3
Pin 3
T amb ≤ 85 °C
Pin 2, pin 3, MIL-STD-883C
Pin 7, MIL-STD-883C
Pin 2, pin 3, MIL-STD-883C
Pin 7, MIL-STD-883C
SYMBOL
V S
I S
V O
I O
P tot
T amb
T stg
V ESD
V ESD
V ESD
V ESD
VALUE
- 0.3 to + 6
3
- 0.3 to (V S + 0.3)
5
10
- 25 to + 85
- 25 to + 85
2000
500
200
100
UNIT
V
mA
V
mA
mW
°C
°C
V
V
V
V
Note
? Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability.
ELECTRICAL CHARACTERISTICS (T amb = - 30 °C to + 85 °C)
PARAMETER
Supply voltage
Supply current (pin 2)
TEST CONDITION
I IN = 0, V S = 5 V
SYMBOL
V S
I S
MIN.
2.5
0.25
TYP.
0.35
MAX.
5.5
0.45
UNIT
V
mA
Output voltage low (pin 3)
Output voltage high (pin 3)
Internal pull up resistor
(pin 2, pin 3)
Max. input DC current
I OL = 2 mA
I OL = 0
V IN > 0
V OL
V OH
R PU
I IN-DCmax.
V S - 0.25
400
33
100
mV
V
k Ω
μA
Min. signal detection current
I IN-DC = 0, f C = f BPF
I IN-DC = 100 μA, f C = f BPF
I IN-min.
I IN-min.
400
5
800
10
pA
nA
I IN-DC = 0, f C = f BPF ,
Output pulse width
Accuracy of bandpass center
frequency
Bandwidth of bandpassfilter
I IN = 0.8 nA to 50 μA,
testsignal see fig. 1, BER ≤ 2%
T amb = + 25 °C
- 3 dB, f 0 = 38 kHz
t po
f BPF
B
t pi - 6/f 0
f 0 - 4 %
t pi
f 0
3.8
t pi + 6/f 0
f 0 + 4 %
μs
kHz
kHz
I IN
V OUT
burst length t pI
output pulse width t po
one carrier cycle 1/f C
I IN
burst length of input signal t pi
output pulse width t po
21538
V OUT
Fig. 1 - Testsignal
Rev. 1.4, 05-Feb-14
2
Document Number: 82443
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
WALLS-C4600-001
SYNJETWIRE HARNESS 4WIRE 600MM
WIT2410SDK
DEVELOPMENT KIT, 2 WIT2410M MODU
WIT2411DK
DEVELOPMENT KIT, 2 WIT2411M MODU
WIT2411SDK
DEVELOPMENT KIT, 2 WIT2411M MODU
WLAD.01
EVALUATION KIT FOR WLA.01
WP1043GD
LED LIGHT BAR SGL 3.65X6.15MM GN
WP1043ID
LED LIGHT BAR SGL 3.65X6.15MM RD
WP1043SGD
LED LIGHT BAR SGL 3.65X6.15MM GN
相关代理商/技术参数
VSOP38338
功能描述:红外接收机 2.7-5.5V 38kHz
RoHS:否 制造商:Vishay Semiconductors 载频:20 kHz to 60 kHz 传输距离:5 m 显示角:+/- 50 deg 高电平脉冲宽度: 低电平脉冲宽度: 最小高电平输出电压: 输出电流:5 mA 工作电压:2.5 V to 5.5 V 电源电流:0.9 mA 功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 25 C 封装 / 箱体: 封装:Reel
VSOP584
制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:Preamplifier Circuit for IR Remote Control
VSOP58436
功能描述:IC SIGNAL CONDITIONING 36KHZ QFN RoHS:是 类别:传感器，转换器 >> 光学 - 光电检测器 - 遥控接收器 系列:* 标准包装:250 系列:*
VSOP58438
功能描述:红外接收机 2.7-5.5V 38kHz
RoHS:否 制造商:Vishay Semiconductors 载频:20 kHz to 60 kHz 传输距离:5 m 显示角:+/- 50 deg 高电平脉冲宽度: 低电平脉冲宽度: 最小高电平输出电压: 输出电流:5 mA 工作电压:2.5 V to 5.5 V 电源电流:0.9 mA 功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 25 C 封装 / 箱体: 封装:Reel
VSOP98260
功能描述:特殊用途放大器 PreAmp for IR Remote CTRL Code Learn’g
RoHS:否 制造商:Texas Instruments 通道数量:Single 共模抑制比（最小值）: 输入补偿电压: 工作电源电压:3 V to 5.5 V 电源电流:5 mA 最大功率耗散: 最大工作温度:+ 70 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-20 封装:Reel
VSOR
制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:Molded, 25 or 50 Mil Pitch, Dual-In-Line Resistor Networks
VSOR1601
制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:Molded, 25 or 50 Mil Pitch, Dual-In-Line Resistor Networks
VSOR1601 102JT
制造商:Vishay Dale 功能描述:RESISTOR NETWORK 1K